Here’s a great way to get introduced to the Rockler/Insty-Drive system! Set contains our exclusive Insty-Driver, #8 high speed steel (HSS) tapered hex shank bit with 4-flute countersink, #2 square drive bit, #2 Phillips power bit, and 1/8" hex wrench. How the Rockler/Insty-Drive System works Drill the pilot hole with the countersink bits or the self-centering bits, which both have a hex shank to prevent slipping.Slip on the Rockler exclusive Insty-Driver, which fits over Rockler countersink and self-centering bits. Magnetic tip holds all 1/4" style insert bits and screws.Drive home the screws. Then slip off the Insty-Driver and do it again. You'll get fast and accurate hardware installation every time! --- Rockler Exclusive Insty-Drive SystemRockler and Insty-Bit have teamed up to give you fast and accurate hardware installation every time! Switch from drilling to driving instantly. Just drill the pilot hole, slip on the Rockler Exclusive Insty-Driver and drive home the screws. It's as easy as 1-2-3! Components are engineered to meet the highest standards for use in industrial applications. They bring together the vest of Innovation from Rockler and Insty-Bit in a precision, time-saving drill and drive system. Plus, all the Rockler/Insty-Drive bits are precision-ground high speed steel (HSS) that keep a sharp edge longer. Made in the USA.The High Speed Steel (HSS) AdvantageAll Rockler/Insty-Drive bits are precision-ground high speed steel (HSS) that resists wear and overheating. High speed steel holds a sharp edge longer even when hot because it maintains temper and hardness. Simply sharpen on a bench grinder. Rockler Exclusive Insty-Drive System Self-Centering BitsEnsures accurate hinge and hardware installation every time. The HSS bit provides perfectly centered and straight pilot holes, so that even an amateur can install shift-free hardware that lasts. The drill guide snugly fits in the hinge countersink, ensuring perfectly centered pilot hole. Without Rockler/Insty-Drive Self-Centering BitsWith Rockler/Insty-Drive Self-Centering Bits Misaligned and damaged screw heads like the example shown above left are virtually eliminated with the self centering bits of the Rockler/Insty-Drive System. Tapered Wood Plug CutterIndustrial quality taper point drill manufactured to ANSI standards.Countersinks made from top quality steel and hardened for extended tool life.Countersink has a 4 flute design for smooth, clean holes that do not require sanding.Taper drill bit is adjustable to match length of screw and is held with 1 or 2 hex set screw. Stop Collar To Control Depth Of CountersinkWood Pre-Drilled Insty-Drive 4 Flute Countersink With High Speed Steel Tapered Drill Wood Fastened.Screw Hidden With Wood Plug1) Select a wood screw size best suited for the project at hand. When selecting screw length, keep in mind that 1/3 of the total length of the screw should be in the piece(s) of wood being attached, and 2/3 should be in the piece of wood to which it is being attached. 2) Use recommended size Taper Drill and Countersink combination (see chart) to pre-drill pilot hole, countersink and counterbore for the screw size of your choice. Position the countersink on the tapered drill so that the point end of the drill extends from the countersink the same distance as the length of the wood screw measured from the head. The locking set screw should be positioned to lock into the flute of the tapered drill. Use the recommended Stop Collar (see chart) if needed to control the depth of the counterbore. Mount the Stop Collar on the Countersink and tighten with set screws.3) Use recommended size (see chart) Plug Cutter to cut tapered plugs to fit over the screw head if the screw is counterbored below the surface of the wood. Plugs can be broken out of the wood with a screwdriver, or the wood can be cut to release the plugs. 4) Attach two pieces of wood by driving screw into pre-drilled hole. Insert wood plug over screw head using a small amount of wood glue. Sand off wood plug flush with surface. Optional Drill Accessories Rockler / Insty-Drive Quick-Change ChuckThe 3/8" shank chuck includes a quick-release sleeve and accepts all 1/4" hex shank bits & drivers. -- (Category: Hand Tools)

Rockler/Insty-Drive 5-Pc. #8 Countersink Set Click Here for the price and more information on the vendor's site for this Rockler/Insty-Drive 5-Pc. #8 Countersink Set. This Rockler/Insty-Drive 5-Pc. #8 Countersink Set product is carried by a family-run company widely known as "the superstore of woodworking." They have what you're looking for. Product: Main category: Hand Tools Name: Rockler/Insty-Drive 5-Pc. #8 Countersink Set Click Here for my list of similar items. Or Here: Shaping Wood: Tools, Plans and Materials for the main category list. To Previous Similar Item | To Next Similar Item Website Copyright © www.ShapingWood.com 2004 -- all rights reserved.